Select Page

servo gear reducer

Wide range of servo gearboxes, made to fit virtually all servo motors on the market
Designed for the highest torsional stiffness and the lowest angular backlash, meant for the utmost torque and overhung loads
Bush with slots and hub clamp for servomotor coupling
Enhanced dimensional compactness because of direct servomotor coupling
Widest range of feasible servomotors coupling dimensions.
The correct technical solution thanks to a comprehensive range of sizes, gear stages, transmission ratios, designs and nonstandard designs.
Servo equipment reducers (worm, coaxial, helical and bevel helical units) Catalog SR
Operating instructions:
Operating instructions for gear reducers and gearmotors (UTD.045)
EP Drive Systems, Inc. is pleased to announce the growth of our range of Servo Reducers, at this point offering five levels of precision to meet up any app requirements. The five levels of precision obtainable allows a machine designer to select the mandatory reducer precision to meet up their requirements and their spending budget. They can be purchased in both in-range and right-angle versions, in torques up to 7,376 lb.ft. and ratios to 3,392:1.
Normal applications for these reducers include rotary & linear axis drives, and material handling axis drives. Industries offered include Material Handling, Automation, Aerospace, Machine Tool and Robotics.
The installation faces of the HT, HP, Electronic and B versions are identical, which makes it possible to interchange a unit with an increased or lower accuracy unit if needed.
A wide range of motor couplings and installation flanges are available for the entire reducer range to install virtually any servo electric motor and the hollow bore output can be used to install output shafts, pinion shafts, or other drive components.
These reducers are usually selected based on the peak cycle forces, which often happen during accelerations and decelerations. These routine forces rely on the driven load, the quickness vs. time profile for the routine, and any other exterior forces acting on the axis. For more selection details, please follow this PDF link.
For application & selection assistance, please call, fax or email us. The application information will be examined by our engineers, who’ll recommend the very best solution for your application.
EP Inc. provides a full range of modular servo gearboxes /worm reducers. The modular style allows for configurations with motor input flange and output pinion for rack and pinion drives, along with solid result shafts, Hollow bore result, and input shafts for all other positioning applications. The modular style allows for universal installation of the gearbox in virtually any orientation.
They can be used on motors with a NEMA23 standard flange through an adaptor package. As the gears are naturally angled, they lead to a short total amount of the motor and its gear.
The series may also be delivered both right- and left-angled and with output shafts on both sides. A 30-mm machine recess for centering and a 4 M5 threaded mounting hole can also be built on the gear’s output side.
Built with a simple and robust design, the series provides gearing ratios that range between 6:1 to 75:1. An individual can also customize the components through the order, in order to match the gear to its intended application.
The Precision Planetary Gears of the EPRG series contains a comprehensive selection of low backlash planetary gearboxes, with up to class 3′ precision, available in several gear frame sizes, with single or multiple stage reduction (for gear ratios from 1:3 to at least one 1:1,000). These models likewise incorporate versions with double shaft, right position shaft and right position output, as well as a full selection of adapters for motor mounting, making them capable of meeting the requirements of also the most diverse applications. They are made for make use of with integrated servo and stepper EP motors, mounted straight or via adaptor flanges, but may also be used with other EP electric motor types. This range of products is founded on years of encounter and represents the end result of a decade-long analysis aimed at improving performance.
Optimum precision and dynamics, combined with outstanding torque density, will be the key requirements specified for reliable servo gearboxes used. EP offers servo gearboxes for any program and any functionality range. Our low-backlash planetary and right-angle gearboxes reflect our enthusiasm for development and the best levels of precision.
Worm gear reducers provide market progress solution with effectiveness and flexibility. Low quantity of basic models can be applied to an array of power ratings guaranteeing best performance and decrease ratios from 5 to 1000.
Gear reducers and servo gearboxes of EP Precision Machinery Co., Ltd. are created for high-performance mechanical gear. When the motor rate needs to be reduced, the output torque raises and send torque totally to the application. We believe that customers will appreciate our equipment reducer to achieve their demand. Just visit EP, you may get more details about servo gearheads, servo gearboxes, and gear reducers. We always keep in the years ahead for your support.
Plug the Speed Reducer in to the desired channel of your receiver, and connect the lead from your servo (or servo wye) in to the male servo lead coming from the circuit panel. The arranged screw on the blue trim pot, located near the top of the main circuit board, can be used to control the quickness of the servo. Change the set screw completely clockwise (CW) for regular servo speed with no speed reduction, completely counter-clockwise (CCW) for maximum speed reduction, or any place in between for partial velocity reduction. The reddish colored LED indicates three possible conditions: Sluggish Blinking = No Signal; Solid On = No Acceleration Reduction; Fast Blinking = Reduced Swiftness Setting
Please note that in the event that you make any alter to the speed establishing as the receiver is on, you need to cycle power to the receiver (switch if off and back again on) for the brand new speed establishing to take effect. This circuit can also be utilized in conjunction with this Servo Reverser to cause flap or retract servos to carefully turn in opposing directions for correct function. Guidelines are included for easy set up and use.
IMPORTANT NOTE: This device will only work on a regular, proportional servo. You won’t work on a retract-type servo, as they do not understand any servo positions apart from clockwise (CW) and counter-clockwise (CCW). Retract servos cannot be slowed down, even by a transmitter which includes this function, as their design and electronics do not allow it. Check the FAQ page to learn more.
This device will reduce the speed of any regular, proportional servo. Connect it between your receiver and the servo (or servos) you intend to control for a far more scale-like movement of flaps or retracts. Adjustable, it could be set to lessen the rate of your servo from super-slow movement to no speed decrease at all, with an nearly infinite quantity of positions in between. Maximum reduction time for a servo to visit 90 degrees is approximately 14 seconds, minimum time (no reduction) is merely the normal speed of the servo. Ideal for reducing or eliminating the inclination of a plane to “balloon up” when flaps are deployed. It can be utilized to control several servo by utilization of a regular servo Y.
This is actually the new regulated version that can be utilized on radio systems powered by any size or type of battery, including 4.8-6.0 volt 4-5 cell Ni-Cad/Ni-MH electric batteries, and HV (high voltage) receivers that are powered by 2-cell 6.6-8.4 volt Li-Po/Li-Ion/LiFE batteries. This unit will NOT reduce the voltage going to your servos.
The EP Gear Reducer may be the perfect solution for servomotor applications such as for example packaging machines, gantries, injection molding machines, pick and place, and linear slides.Offered in concentric shaft, correct angle solid shaft, and correct angle hollow shaft designs with modular adaptor flanges and keyless compressible bushings to quickly mount to any kind of manufacturer’s servo motor. The EP Series helical gears possess slanted teeth compared to spur gears with directly cut teeth, making a smoother equipment mesh, yielding considerably lower noise levels.
The reduced backlash EP planetary servo gear units are created for the 30 to 350 Nm (265 to 3100 lb-in) torque classes. They were designed to combine the best possible flexibility and cost-efficiency because don’t assume all application requires high-performance parts.
They offer a basis for diverse, dynamic and cost-optimized drive solutions.
The EP planetary servo equipment units can be found in the following versions:
PSC = B5 output, soft output shaft
PSKC = B5 output, with keyway
PSCZ = B14, result, smooth output shaft
PSKCZ = B14 output, with keyway

There is fantastic value in taking some time to comprehend the subject of servo gear reducer, but the Internet may or could not be your best source of info.

Recent Posts

worm drive motor

As one of leading worm drive motor manufacturers, suppliers and exporters of mechanical products, We offer worm drive motor and many other products.

Please contact us for details.

Mail: [email protected]

Manufacturer supplier exporter of worm reducer